hydmech-c3502av

HYDMECH C350-2AV Manual Vertical Column Cold Saw

The HYDMECH C350-2AV Cold Saw is a solid addition in every metal fabrication shop. It is a smaller circular saw that is a manual vertical column cold saw and is favored for its accurate, quick and clean metal cutting.

Features and benefits

The HYDMECH C350-2AV Cold Saw miters from 60 degrees left to about 45 degrees to the right.  It features a range of 4 dissimilar blade speeds and a 4 1/2’’ round hollow capacity, 2.5/3.0 HP motor and 14’’ blade which makes it the ideal choice when quick and clean metal cutting is needed. The carbide circular saw along with HYDMECH’s quality guarantee ensure you get the best cuts in the industry.

Standard features

  • Has a heavy duty sawing head that has a manual pull-down movement based on adjustable dual precision linear bearings.
  • Has four blade speeds- 15, 30, 45 and 90 rpm.
  • Has an air-filled operating vise, which through a foot pedal is able to slide on dovetail in order to adjust with saw head mitered position.
  • Has an enclosed steel base that has a chip drawer and a coolant tank.
  • Has a flood coolant system that has a coolant tank.
  • Has an adjustable material stop with a ruler
  • Has a wire chip brush
  • Has an ergonomically positioned control panel that includes a main disconnect switch, a minimum tension coil, a thermal relay, an emergency stop button and a safety door interlocks.
  • Has a cutting head that is balanced by a gas spring.
  • Has a rotating table on a center pin

Available options

  • 350 mm cold saw blades
  • K40 roller table

DETAILED SPECIFICATIONS

Rectangular Capacity at 90° 7” H x 3 3/4” W
Blade Size Max: 14″
HP 2.5 / 3
Mitering 60° left and 45° right
Operation Manual

BANDSAW PARTS AND SERVICE

Fabtech Solution is a trusted dealer of HYDMECH Band Saws, our service department regularly repairs and maintains wood and metal cutting bandsaw machinery. We carry complete lines of replacement blades, aftermarket parts and blade coolant. A large selection of bi-metal, grit and carbide tipped bandsaw blades as well as Fluid and Drip Lubricants. We can ship and deliver to your shop. Our Service Department will keep your saw in motion.

We've included several resources and troubleshooting guides below. This material is for reference purposes only; please contact our Service Department with any questions or concerns.

Contact our Service Department today with any questions.

TROUBLESHOOTING ISSUES

What type of hydraulic oil is used on HYDMECH machines?
Texaco Rando HD46 or equivalent or machines built with Parker or Bosch Rexroth Power Packs use Shell Tellus 22 or equivalent hydraulic oil. The fill level is marked as a black line on the temperature / level gauge.
What hydraulic oil filter is used on HYDMECH saws and how often should it be changed?
HYDMECH uses commercially available filters. When calling to order filters, please refer to the information listed on your current filter to obtain the proper dimensions as different sizes are used. Filters should be changed after the first 50 hours of operation and then every 500 working hours after that.
My saw runs, but I have no hydraulic functions or any pressure showing on the system pressure gauge.
Between the hydraulic pump and motor there is a bell housing containing a three-piece coupling. Inspect the coupling to see if one of the flanges has loosened and slid apart. If it is necessary to re-connect the coupling, use removable Loc-Tite on the set screws, or if the coupling is damaged, it will need to be replaced. With new saw installations, if there is no pressure showing on the system pressure gauge, it is likely that the phase wiring is backwards. Reverse any two of the three phase wires supplying power to the saw.
On my inverter driven machine the blade shuts down and will not restart.
Disconnect the supply voltage to the saw for approximately five minutes. Turn the power back on and try to restart the saw blade. If the alarm or fault code persists, check the led screen on the blade motor inverter drive for the presence of an error code, call the factory with the saw serial number, inverter model number and the error code.
My chip auger has stopped turning on my saw.
The chip auger may be jammed with a thin piece of metal. If you are unable to locate or remove the obstruction, you need to reverse the auger rotation. Lower the head fully down, shut off the hydraulics, and reverse the two conveyor hoses at the hydraulic manifold. Start the hydraulics, raise the head, and switch the head to the down position and the chip conveyor will run in reverse dislodging the piece of metal. Then put the hoses back as they were initially.
ALARM LIST MEP32 – X AXE MOTOR
99 SHS Transmission/Reception 94 Micro zero-axe in-congruent
98 SHS In-congruent reception 93 SHS phases short circuit
97 Micro zero-behind 92 SHS driver over temperature
96 Micro zero-axe always OFF 91 SHS over/under-voltage
95 Micro zero-axe always ON 90 Non-existent phase zeroing
DRIVER STEPPER – ALARM LIST

Description

Possible Cause

d

Disable drive Press Reset. If display doesn’t show “r” letter, please check limit switch, emergency circuit,…

r

Enable and ready drive Ready to march.

c

Phase motor short circuit Check the connection on driver and motor.

u

Hi or low voltage supply Check the power supply voltage, transformer, connections.

t

Over temperature Check if fans inside the cabinet are turning properly, fuses…
Contact our Service Department today with any questions.
FABTECH SOLUTIONS offers the most competitive pricing available.

Our Sales Department offers extensive industry knowledge and experience to help you find the best metalworking equipment and machinery for your unique solution. Whether your looking to purchase new metal fabrication equipment or used fabrication machine tools, we will source your product through our industry network.
Give us a call today! (864) 518-0629